Rockford Electrician GuideIndependent homeowner guide ยท not an electrician

Rewiring an older home in Rockford

Last reviewed November 18, 2026 against City of Rockford sources.

Rewiring ranges from replacing a few circuits to rewiring a whole house. Either way it is permit work in Rockford, and the City's local amendments to the 2020 National Electrical Code (Ordinance No. 2024-175-O, effective January 1, 2025) set several rules that are stricter than the base code. (City of Rockford local amendments)

Rockford rules that shape a rewiring job

Aluminum branch wiring. Rockford amended NEC 310.3(B) so that aluminum and copper-clad aluminum conductors are "prohibited to be installed in sizes smaller than 4 AWG."

No push-in connections. Rockford added NEC 300.13(D): no push-type or clamp-type connections for splices or device terminations "unless the wire connection is secured with a screw or crimping tool." Exceptions are ballast disconnects and factory terminations in light fixtures. Ask whether devices will be screw-terminated.

Devices are not splices. A switch or receptacle "may not be used to provide electrical continuity to any circuit conductor" (amended 300.13(C)).

Protect exposed cable. In unfinished areas, exposed NM cable 7 feet or closer to the floor must be protected with a durable building material or sleeved in an approved manner (added 334.15(D)). This often matters in basements.

Tie wire is not support. Tie wire may not be the only means of supporting conduit or cable above ground (added 300.11(A)(1)).

Where NM cable is allowed. Rockford limits Type NM, NMC and NMS cable to R-2, R-3 and R-4 structures (as defined by the International Building Code) not more than three floors above grade (added 334.10).

Arc-fault and ground-fault protection

Rockford keeps arc-fault (AFCI) protection for 120-volt, 15- and 20-amp branch circuits in dwelling kitchens, family rooms, dining rooms, living rooms, bedrooms, closets, hallways, laundry areas and similar rooms (amended 210.12(A)). The Electrical Safety Foundation International describes an arc fault as a dangerous problem caused by damaged, overheated or stressed wiring or devices, for example when older wires become frayed or cracked. (ESFI: AFCIs) GFCI locations are on our outlets page.

Opening walls: when a permit is triggered

The City exempts some wall and ceiling repair from permits, but only if, among other conditions, no more than 50% of the coverings in a room are removed, wiring in a hazardous condition is not exposed, and electrical systems are "not being resized, rearranged or added to." Rewiring rearranges and adds wiring, so it needs a permit. (City of Rockford FAQ)

The City inspects rough-in before wiring in walls, ceilings or soffits is covered, and does a final inspection after all work is complete. Plan drywall work around the rough-in inspection. (City of Rockford: Electrical Permits)

If the City has ordered a repair

If the City has issued an "Order to Repair," the 2026 fee schedule has a separate residential Order to Repair permit fee (0.55% of the total reported value, $13 minimum). See Rockford costs. (2026 fee schedule)

What to ask before you sign

  • Which circuits are being replaced, and which existing wiring stays?
  • Will the panel be touched? If so, Rockford's 230.11 whole-service rule may apply; see panel upgrades.
  • Who repairs the wall openings, and is that in the price?
  • Who pulls the permit, and what is the contractor's City of Rockford registration number?

Questions

Can new aluminum branch circuits be installed in Rockford?

Rockford's amended NEC 310.3(B) says aluminum and copper-clad aluminum conductors are "prohibited to be installed in sizes smaller than 4 AWG."

Does Rockford allow push-in (backstab) connections?

Not unless the connection is secured with a screw or crimping tool. Rockford added NEC 300.13(D), with exceptions only for ballast disconnects and factory terminations in light fixtures.

Do I need a permit to rewire part of my house in Rockford?

Yes. The City's exemption for wall and ceiling repair does not apply when electrical systems are being resized, rearranged or added to.

Sources